元器件交易网www.cecb2b.comMOTOROLASEMICONDUCTOR TECHNICAL DATA9ĆBit Shift RegisterThe MC10E/100E142 is a 9-bit shift register, designed with byte-parityapplications in mind. The E142 performs serial/parallel in andserial/parallel out, shifting in one direction. The nine inputs D0–D8accept parallel input data, while S-IN accepts serial input data. The Qnoutputs do not need to be terminated for the shift operation to function. Tominimize noise and power, any Q output not used should be leftunterminated.700MHz Min. Shift Frequency9-Bit for Byte-Parity ApplicationsAsynchronous Master ResetDual ClocksExtended 100E VEE Range of –4.2V to –5.46V75kΩ Input Pulldown ResistorsThe SEL (Select) input pin is used to switch between the two modes ofoperation — SHIFT and LOAD. The shift direction is from bit 0 to bit 8.Input data is accepted by the registers a set-up time before the positivegoing edge of CLK1 or CLK2; shifting is also accomplished on the positiveclock edge. A HIGH on the Master Reset pin (MR) asynchronously resetsall the resisters to zero.SEL25MRCLK1CLK2VEES-IND0D126272812345671011D3D824D723D622D521VCCO20Q819181716Q7Q6VCCQ5VCCOQ4Q3D1S-IND0MC10E142MC100E142••••••9-BIT SHIFTREGISTERFN SUFFIXPLASTIC PACKAGECASE 776-02LOGIC DIAGRAM10DQQ0Pinout: 28-Lead PLCC(Top View)1514131210DQQ1D21010DQQ2D2D3D4VCCOQ0Q1Q2* All VCC and VCCO pins are tied together on the die.DQQ3PIN NAMESPinD0 – D8S-INSELCLK1, CLK2MRQ0 – Q8Parallel Data InputsSerial Data InputMode Select InputClock InputsMaster ResetData OutputsFunctionD8SELCLK1CLK2ModeMR10DQQ8FUNCTIONSSELLH12/93LoadShift© Motorola, Inc. 19962–1REV 2元器件交易网www.cecb2b.comMC10E142 MC100E142DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)0°CSymbolIIHIEECharacteristicInput HIGH CurrentPower Supply Current10E100E120120mintypmax150145145120120min25°Ctypmax150145145120138min85°Ctypmax150145165UnitµAmAConditionAC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)0°CSymbolfSHIFTtPLHtPHLtsCharacteristicMax. Shift FrequencyPropagation Delay to OutputClkMRSetup TimeDSELHold TimeDSELReset Recovery TimeMinimum Pulse WidthClk, MRWithin-Device SkewRise/Fall Times20 - 80%300min700typ900maxmin70025°Ctyp900maxmin70085°Ctyp900maxUnitMHzps600600503003007590040075525800300800800–100150100–15070010001000600600503003007590040075525800300800800–100150100–15070010001000600600503003007590040075525800pspsNote 1800800–100150ps100–150700psps10001000psConditionthtRRtPWtSKEWtrtf1.Within-device skew is defined as identical transitions on similar paths through a device.MOTOROLA2–2ECLinPS and ECLinPS LiteDL140 — Rev 4元器件交易网www.cecb2b.comMC10E142 MC100E142OUTLINE DIMENSIONSFN SUFFIXPLASTIC PLCC PACKAGECASE 776–02ISSUE D0.007 (0.180)UMB-N-Y BRKDZ-L--M-TL–MMSNSS0.007 (0.180)TL–MNSW281DXVIEW D-DG10.010 (0.250)SVTL–MSNSAZR0.007 (0.180)0.007 (0.180)MTL–MTL–MSNNSH0.007 (0.180)MTL–MSNSMSSCGG10.010 (0.250)SE0.004 (0.100)J-T-SEATINGPLANEK1KFVIEW S0.007 (0.180)MVIEW STL–MSTL–MSNSNSNOTES:1.DATUMS -L-, -M-, AND -N- DETERMINEDWHERE TOP OF LEAD SHOULDER EXITSPLASTIC BODY AT MOLD PARTING LINE.2.DIM G1, TRUE POSITION TO BE MEASUREDAT DATUM -T-, SEATING PLANE.3.DIM R AND U DO NOT INCLUDE MOLD FLASH.ALLOWABLE MOLD FLASH IS 0.010 (0.250)PER SIDE.4.DIMENSIONING AND TOLERANCING PER ANSIY14.5M, 1982.5.CONTROLLING DIMENSION: INCH.6.THE PACKAGE TOP MAY BE SMALLER THANTHE PACKAGE BOTTOM BY UP TO 0.012(0.300). DIMENSIONS R AND U AREDETERMINED AT THE OUTERMOSTEXTREMES OF THE PLASTIC BODYEXCLUSIVE OF MOLD FLASH, TIE BARBURRS, GATE BURRS AND INTERLEADFLASH, BUT INCLUDING ANY MISMATCHBETWEEN THE TOP AND BOTTOM OF THEPLASTIC BODY.7.DIMENSION H DOES NOT INCLUDE DAMBARPROTRUSION OR INTRUSION. THE DAMBARPROTRUSION(S) SHALL NOT CAUSE THE HDIMENSION TO BE GREATER THAN 0.037(0.940). THE DAMBAR INTRUSION(S) SHALLNOT CAUSE THE H DIMENSION TO BESMALLER THAN 0.025 (0.635).DIMABCEFGHJKRUVWXYZG1K1INCHESMINMAX0.4850.4950.4850.4950.1650.1800.0900.1100.0130.0190.050 BSC0.0260.0320.020— 0.025— 0.4500.4560.4500.4560.0420.0480.0420.0480.0420.056— 0.0202° 10° 0.4100.4300.040—MILLIMETERSMINMAX12.3212.5712.3212.574.204.572.292.790.330.481.27 BSC0.660.810.51— 0.— 11.4311.5811.4311.581.071.211.071.211.071.42— 0.502° 10° 10.4210.921.02—ECLinPS and ECLinPS LiteDL140 — Rev 42–3MOTOROLA元器件交易网www.cecb2b.comMC10E142 MC100E142Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regardingthe suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, andspecifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motoroladata sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights ofothers. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or otherapplications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injuryor death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorolaand its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney feesarising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges thatMotorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an EqualOpportunity/Affirmative Action Employer.How to reach us:USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609INTERNET: http://Design–NET.comJAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., . 852–26629298MOTOROLA◊2–4*MC10E142/D*MC10E142/DECLinPS and ECLinPS LiteDL140 — Rev 4
