无机硅酸锌车间底漆

无机硅酸锌车间底漆

无机硅酸锌车间底漆一种在储存、建造及装配过程中，用于经喷砂清洁的钢板或其他钢结构提供短到中期保护的车间底漆，专为自动喷涂线而设计，一种性价比较高Intended 的防腐涂料。 Uses As a shop primer, it is suited for painting the steel plate especially which is blasted, it can protect the steel structure for a short or middle time during the process, construction and fabrication, It is specially designed for the auto-spray quipment. 二罐装含硅酸乙酯车间底漆、灰色。具有耐候性、焊接及切割性能好、烧伤面积少、Product 耐热性佳、保护期强。 用途 Description Two packages, contains zinc tetraethyl silicate, gray, Excellent resistance to deterioration on Weathering, welding and cutting-through property, ablation resistance, 产品简介 heat-resistance and long time protection. Volume Solids 固体份 ≥28 15-20 microns, according to the protected period Product Dry Film Thickness干膜厚度 15-20微米，视保护期限要求 14.36 m2 /Kg 14.36平方米/公斤 Allow appropriate loss 允许适量损耗 A : B=2:1(by weight) 甲:乙=2:1 Information 产品数据 Theoretical Coverage 理论涂布率 Practical Coverage 实际涂布率 Mix Radio 混合比 Method of Application 施工方法 Airless Spray 无空气喷涂 Recommended 推荐采用 Application Details 施工详述 Brush or Roller 涂刷或辊涂 Suitable, only for repairing 可以采用，仅限于修补 Conventional Spray 传统喷涂 Adoptable, but thinning and stirring are necessary 适用，需稀释，使用带搅拌器的适当设备。 Thinner 稀释剂 C007 Cleaner 油漆设备清洗剂 C007

Pot Life 使用期 5℃:10 h ； 20℃ 8小时 ；35℃ 4小时 Storage 贮存期 six months 6个月 Touch Over coating Interval Substrate Hard Dry Dry Drying time 覆涂间隔 Temperature 硬干 表干 干燥时间 Mix最短 Max最长 底材温度，℃ （h） （min） 25 1-3 3-5 5 h / Storage 贮存 Store in cool and dry conditions 贮存于阴凉干燥处 Storage and Handling Pack size 包装规格 A;18 Kg in 20 liter container 甲:18公斤装于20公升容器中 B:9 Kg in 10 liter container 乙:9公斤装于10公升容器中 贮存与管理 Flash Point 闪点 Above 13℃(mixture) 13℃以上（混合物） Specific Gravity 比重 Approx1.35 Kg/L 大约1.35公斤/公升 The steel surface: oil and grease removed with proper cleaner, Blast clean to Swedish Standard SIS055900 Sa2.5 The coarseness should be between 40 microns and 75 Specification microns and 钢材表面用适当的清洁剂除去油和脂，喷砂处理达瑞典标准 SIS055900 Sa2.5级，Surface 表面粗糙度达40-75微米 preparation 技术要求及表面处理 Recommended coat: Pray one coat with high-pressure airless spray and the dry film thickness should be 15-20 microns, Subsequent coat: Epoxy resin paint, coat-tar epoxy Limitations paint, chlorinated rubber paint, polyurethane paint, chlorosulphonated polyethylene paint, heavy duty paint based on highly chorinated polyethylene etc. 限制 建议涂装道数：高压无空气喷涂一道、干膜厚度达15-20微米 后道配套涂料：环氧树脂涂料、环氧沥青涂料、氯化橡胶涂料、聚氨酯涂料、氯磺化聚乙烯涂料、高氯化聚乙烯防腐涂料。 The product must be used in painting area by professionals. When painting, please be sure to refer to Product Data Sheet and MSDS. Consult our company if consumers

could not completely understand the precautions for safety and health when applying the product. The product is a kind of solvent-based paint. In order to avoid the accident or dangerous occurrence, minimal safety precaution, as follow, should be down. The paint contains volatile solvent and it is flammable, So must keep away from sparks and open flames. No smoking at workplace, Effective precautions (such as using explosion-proof electrical equipments. No static electricity accumulation or metal collision etc) also should be done so as to avoid product sparks. Enough ventilation is necessary at application sites. In order to remove any danger of explosion, must keep the ratio of gas / air is less than 10 %, Usually 200 m3of ventilation quantity per 1 Kg solvent (according to the solvent) is necessary, it canMaintain the minimum explosive limit. Take effective precautions to prevent skin and eye contact with the coating (such as the use of overalls, gloves, goggles, face shields and protective oil coating and so on). If paint gets in touch with skin,If accidental skin contact with the product, please use fresh water and soap or an appropriate industrial cleaning agents thoroughly cleansed. In case of eyes being contaminated, rinse with fresh water for 10 min at least and give medical treatment immediately.During painting, it is recommended to wear face shields to prevent inhalation of paint mist and harmful gases.Especially in poorly ventilated Safety environment, it is more necessary.Finally, be handled with care so as not to waste Precautions paint barrels of pollution of the environment. 安全措施 NOTICE: If consumers have not taken effective safety precautions (Refer to the specification), our company will NOT be responsible for any accident. 无机硅酸锌车间底漆必须由专业人员在工业场所使用。使用时请务必参照本说明书以及相关健康安全手册。若客户在使用本产品前,未能详细了解本产品的相关健康安全知识,请与本公司人员联系。 该涂料为溶剂型涂料，为避免事故或危险发生，应采取最低限度的安全措施如下： 此涂料为易燃物,并含有挥发性易燃溶剂，故必须远离火星和明火。 严禁在作业场所吸烟，并应该采取有效措施，防止火星产生(如采用防爆电器设备，杜绝静电积累,避免金属撞击等)。 施工场所应尽量保持良好通风。为消除使用过程中的爆炸隐患,应保证足够的通风量以维持气体/空气比例不超过最低爆炸极限的10 %,通常每千克溶剂需要200立方米通风量,(与溶剂种类相关)就能维持最低爆炸极限10 %的工作环境。 采取有效措施，防止皮肤和眼睛与涂料直接接触(如使用工作服,手套,护目镜,面罩及涂防护油等)。若皮肤不慎与产品相接触,请用清水及肥皂或适当的工业清洁剂

彻底清洗；若眼睛受到污染,请即刻用清水冲洗至少10分钟,并立即就医。 在施工时，建议佩戴面罩以免吸入漆雾和有害气体，尤其在通风不良的环境下，更要注意。最后请谨慎处理废旧漆桶以免污染环境。 责任声明：对于未按本公司所要求采取有效得安全措施而引起的安全事故,本公司不负任何责任。 来源 江苏纽克莱涂料有限公司http://www.nsk-paint.com